Buy BAK Industries R15311 RollBak G2 Aluminum Hard Retractable Tonneau Bed CoverBAK Industries R15311 RollBak G2 Aluminum Hard Retractable Tonneau Bed Cover Product Description:
- 100% Powder coated aluminum
- Automatic, intermittent locking system that securely locks the cover at every 12 inch interval of the bed
- No interference with tailgate
- Water- Resistant
- Sleek low profile aerodynamic design improves gas mileage up to 11%
Product Description
The Rollbak Generation 2 (G2) Tonneau Cover a 100% Powder Coated Aluminum Hard, Retractable, tonneau cover that gives you instant access to your truck bed and cargo without ever removing the cover. Better yet, this cover does not interfere with stake hole pockets, so you can keep those tubular bed rails without having to remove them. You can even use this cover with your existing ladder rack and your tie downs. This cover is level with the truck bed, so you maintain your truck's original sleek profile. The rollbak G2 is almost 100% maintenance free and glides with ease. It is a COMPLETELY NEW design with far fewer moving components and state of the art, professional grade finishes throughout! This rollbak is super easy to install. It’s pretty much completely assembled and set at factory level. Even the components like locks, spring tension and rails are all ready to go and assembled right out of the box. If you haven’t seen the new rollbak G2 yet, get ready to be impressed! This revolutionary design is truly "Armor for Truck Beds" and is built to outlast your truck! This cover turns your truck bed into a secure armored trunk. If you are looking for an extremely tough, good-looking, secure truck bed cover that is amazingly versatile, then keep reading!
Customer Reviews
Most helpful customer reviews
1 of 1 people found the following review helpful.
Nice cover, easy install
By Michael David
I ordered this cover and was glad to see it was American Made. The box arrived and had a hole in it and the small clamps were missing but the company shipped them out to me right away.The instructions were a little vague but if you have any mechanical aptitude you won't have a problem putting this together although I did end up with two extra jack screws that were shipped with the clamp kit and I can't figure out anywhere where these go. I had someone help me install the canister portion and I did the rails and everything else myself in around 2 hours. I installed the drain tubes but didn't pass them through the truck bed since I didn't want to cut the rubber in the truck unless it was necessary. Where I live in Southern California we don't get a lot of rain and even after car washes I haven't noticed any water inside the bed of the truck.Pros:1. Nice looking cover, I had a Pace Edwards Jack Rabbit on my previous truck and I liked the look of this one better and the way they have the latch underneath the cover is nicer since it's one less key to carry.2. low profile design3. powdercoated aluminum construction, The vinyl cover on my last truck faded bad4. easy installation5. priceAfter installation, there were some design flaws though that I had to do work-arounds for1. On my Pace Edwards I turn the latch on the cover and it rolls up completely and then automatically undoes the latch so it is ready to close. On this cover you have to hold the latch as you opening it over each of the adjust side lock posts. What I ended up doing was moving the side lock locations so it only locked in a couple of positions so I wouldn't have to walk down the side of my truck (longbed) everytime I wanted to fully open the cover.2. Although the locks hold the cover secure if you let it slam into the locks while opening the cover it will bypass the lock and keep going. One time it even rolled itself back into the cover which took me a few minutes to get it pulled back out. I have since then added a set of the locks (the kits come with extras) just before it hits the canister to make it a little more secure and it hopefully doesn't go back into the canister again.Overall, I am pleased with this cover and would recommend it for it's price.
1 of 1 people found the following review helpful.
AWESOME!
By ECH
After searching for 6 months for the right cover for my truck bed, I came across the Rollbak G2. It wasn't terribly difficult to install but the instructions were a bit confusing. Aluminum planks are uniform and no blemishes on the finish. Sits very low profile and the space loss at the end of the bed is not that bad (1 ft give or take)The unit itself looks great and is perfect for my truck. I have received many compliments. So much so that I have become a dealer for the product. To be honest, the dealer pricing and the price on amazon are very close. I would suggest this to ANYONE who is looking for a roll over toneau cover.
1 of 1 people found the following review helpful.Awesome cover
By Angler
I've had several hard tonneau covers and this is by far the best. It looks great and I get comments on it all the time. It is a very clean install and looks like it belongs on the truck. If you pick up something that won't fit under the cover, no problem like with some other covers. You simply roll it up and put the big item in there. Installation was easy. My only complaint on install was where the instructions have you set the side rails relative to the tailgate. The instructions read (to me) that the rails need to be a certain distance from the tailgate and following those instructions left a gap between the rubber seal on the cover and the tailgate. However, you don't get to test that gap until the very end. So I had to go back and loosen the side rails to get it to seal properly. Other than that, it was perfect.
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!
